Bass Pro Shops   Daveys Locker Sportfishing  Newport Landing Sportfishing   The Fishing Syndicate  Carver Covers  Tight Lines Guide Service  Bob Sands Fishing Tackle 
Page 1 of 2 12 LastLast
Results 1 to 10 of 19

Thread: Boat trailer bearings 101... Every boat owners need to know how

  1. #1
    Join Date
    Sep 2010
    Location
    Bakersfield
    Posts
    6,388

    Default Boat trailer bearings 101... Every boat owners need to know how

    So being a boat owner for years, I learned real quick how to keep the trailer bearings in working order.

    Every season they should be inspected and greased. Shops will charge upwards of 200 dollars for 5.00 bucks worth of grease.

    Learn to do this yourself, save tons of money and come with the grips of understanding the mechanical workings of your axle.

    I've seen many boats on the side of the road with no tires, burnt axle, etc,,,,..

    So I took a week and worked on Double A's rig. Rebuild carb, new fuel lines, rebuild fuel pump, change out and repair poppet valve and replace Thermostat and changed the lower unit oil

    Took the time to show Double A how to regrease/replace his trailer bearings and now he is set for a season of fishing with no doubt of save travel.

    First off, I named his boat the party animal,,, He's blasting the 1987 sticker on the windshield.



    Had some fun at his expense



    Well here we go..

    Standard wheel removal.. break lugs free before you jack



    Wheel is off



    Inspect and remove line and such that could tear your seal, like this boat had



    Next is the bearing buddy removal, if you have just a hub cap it works the same.

    Strike once with the mallet or hammer {hammer not prefferred} one direction, then opposite, repeat... Take turns striking from each side



    As you can see its just pressed in



    Now for a little pet peave about Bearing Buddies.

    It is common for owners of trailers with bearing buddies to swear off trailer bearing maintenance with a false sense of security that the Bearing buddy keeps the water out and greased bearings.

    Bearing buddies DO NOT keep water out, they help.

    Bearing buddies Do NOT prevent bearing wear

    All they do is spring load a supply of pressurized grease into the hub, which aids in keeping water out and pushing grease to the bearings. Bearings will still wear, water will always get in eventually.

    Here is how a BB works, That spring on the inner lip compresses grease behind the plate and forces grease back applying pressure



    Heres the plate on the backside



    OK back to the tutorial

    With the BB out of the way, Its time to remove the cotter pin that is locking the castle nut in. Both pictured in the grease



    With the castle nut off the entire hub will slip off the axle spindle



    Here is the spindle, notice the discoloration from being hot at some point in time. {probably PO burnt bearings}



    With the hub off, the front bearing slides out, the bearings on this boat were in like new condition, I did not pull the race out, as they were in like new condition also.



    With the front bearing out its time to knock out the back seal and bearing. You will need a long punch and make absolutely sure you are striking the meaty part of the back bearing and not any part of the flimsy seal as it will warp and no longer function as a seal.

    Here is the back side and a view of the seal



    How to place the punch to catch that back bearing



    Sucessful removal



    Now clean inside the hub and use solvent based cleaners to clean old grease from the bearing cavities

    In this pic you will notice the race I spoke of earlier, That race accepts the tapered bearing, the bearing spins on the spindle and race and the race is wedged into the hub. Now if you have to replace worn bearings you MUST replace the race as well.

    Same method for removing the race as the back side bearing and seal, Strike with a punch from opposite end. Now when installing new races, Use an exact fitting socket or pipe. DO NOT scar the inner lip of the race with punches or screw drivers, it will destroy a new bearing



    See the angled race inside?



    Here is the complete hub components. Cleaned and ready for regreasin and installation.



    When regrease, make sure you push the new grease up and through the cage that holds the roller bearings



    Made two quick vids on how to push the grease through







    Reinstall greased bearing in the back fitting on the race perfectly, make sure to smear some grease on the race first. Then tap the seal back in





    pack a handful of grease inside the hub and slip back on the spindle



    Slide the front bearing back on, then the washer spacer between the bearing and castle nut, hand tighten the castle nut, then use your wrench and tighten the castle until you cannot freely spin the hub, this is setting the bearings to the race.. Once you cannot spin the hub, back off until the hub spins freely and make sure there is no side to side play in the hub.

    Backing off the castle should only be 1/4 turn or so, Once your comfortable with the friction of the hub, slide the cotter pin through the castle nut into the hole in the spindle and bend the cotter, locking the castle nut



    Tap the Bearing buddy back on, shoot some grease in with a grease gun until the spring is compressed and reinstall tire and thats it!



    Only tools you will need are a Mallet, Crescent wrench, long punch and pliers for the cotter pin



    You older boat guys, do yourself a favor and inspect and regrease. Save ya tons of money from having to pay a guy or having a tow truck pick your rig up from the side of the freeway.

  2. #2
    Join Date
    Nov 2010
    Location
    Castaic
    Posts
    1,117

    Default

    Crescent wrench... check

    Mallet... check

    Punch... check

    Case of beer... check

    Ready to roll

  3. #3
    Join Date
    Sep 2006
    Location
    Live in Whittier
    Posts
    1,133

    Default

    Very nice informative write up Mike.

    This should be a sticky for changing bearings.

    On another note, kinda funny that you pulled a Di/do out of your bathroom to plant it on DA's boat. Haha

    Nonetheless, great job!!!!!

  4. #4
    Join Date
    Mar 2009
    Location
    s.p
    Posts
    1,864

    Default

    good info remindes me its time to do mine

  5. #5
    Join Date
    Nov 2009
    Location
    Whittier
    Posts
    2,455

    Default

    Great advice,love the other lubricating tools (Silver Bullets).

    Cya TunaVic

  6. #6
    Join Date
    Mar 2004
    Location
    Palmdale <*))))>{
    Posts
    2,618

    Default

    i have been on the side of the road for 3 hours waiting for a tow truck. now i grease them every time i get home from the lake. buddy bearings. yeah!!!

  7. #7
    Join Date
    Jul 2004
    Location
    Quartz Hill, CA
    Posts
    8,306

    Default

    I think you needed to use more coors light,,,,carpboy,,,,,,,,,,,,,,,,,,,,,,,

  8. #8
    Join Date
    Nov 2009
    Location
    Rat Beach
    Posts
    7,272

    Default

    Great post.
    Harold Davis of Davis boats also recommends waiting 20 - 30 minutes for the bearings to cool down prior to launch. Hot bearings into cool water will have the grease displaced by water.

    Also a digital point and shoot thermometer can help to check bearing temps after a tow to see if one is hotter than the others.
    DR

  9. #9
    Join Date
    Sep 2010
    Location
    Bakersfield
    Posts
    6,388

    Default

    Quote Originally Posted by DockRat View Post
    Great post.
    Harold Davis of Davis boats also recommends waiting 20 - 30 minutes for the bearings to cool down prior to launch. Hot bearings into cool water will have the grease displaced by water.

    Also a digital point and shoot thermometer can help to check bearing temps after a tow to see if one is hotter than the others.
    DR

    Yup. Hot bearings and hot hubs dipped into cold water causes the warmer air/grease inside the hub to contract or cool quickly drawing in water

  10. #10
    Join Date
    Jul 2007
    Location
    BAKERSFIELD
    Posts
    5,480

    Default

    Cutbait,,did you rob my fridge again?

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •